HomeFreebiesBoatingOutboard Engine Wiring

Outboard Engine Wiring

Outboard engine color wiring diagram

Previous articleICAST 2010 Roundup
Branson Werner
Branson Wernerhttp://www.bransonwerner.com
When not working his heart out on websites, e-commerce, and programming, Branson like to enjoy time on the lake. His best times are spent with friends trophy bass hunting in Southern California.
RELATED ARTICLES

22 COMMENTS

  1. kill switch was not installed during engine changeout and now boat quit on me and all indications are kill switch wiring jump out has came loose. motor is a 2003 225hp honda 4stroke, what color would the wires be, help

  2. I have an 85hp force that is prewired with 15ft of harness want to install motor on a 19ft sunbird boat that used to have a merc on it need help on the color difference of the wires from one brand to the other. Can anyone help?

  3. I have a 2007 bass tracker pro team 170 with a 25 hp mec efi. I replaced the battery’s and now it won’t start. I did get the light to work. Help me if you can, please.

  4. Hello, I have a 1991 Nitro Tracker 175 fish and ski. All of a sudden none of my electric accessories (gauges, depth finder, bilge pump, etc.) will work. I can only find one fuse and that located in a small plastic cover right on the motor. Can anyone PLEASE tell me where I can find a fuse panel? I would expect it behind the dash but there doesn’t seem to be one. Anyone out there smarter than me? PLEASE HELP. Thanks! Lydell

  5. ignition switch broke got a new one no power to switch all fuses are good power every where else 2010 bass tracker 175 txw

  6. I have a 2008 Sun Tracker party barge 190 50 horse Mercury. Replaced battery started boat ran for bit changed out spark plugs and went to restart and there is no power what so ever like the battery is dead or a fuse blown help ?

  7. can someone help me with color code when connecting a Suzuki remote control na12s to a Suzuki dt 85 hp 1980 model. I hoped the colors in cable would match those in plug on motor but no such luck. oh the motor has power trim. help please

  8. I have a Sun Tracker 2003 with a 60hp 2 stroke Merc. I just had voltage regarding replaced and now tach is not working and my trim switch on throttle works for down but not to raise it.It’s works fine on motor. Can you tell me how to get at switch to check, also tach.Much thanks for any help.

  9. while replacing both gaskets on 40hp 2 stroke 95 mercury adapter plate gaskets all wires that unplug were done so having trouble getting wires back righi motor cranks but will not shut off please help thanks

  10. i have a 2009 150 honda 4 stroke and now want and have found 225 in 2008 honda 4 stroke. Will this hook up to the existing wiring in my harris pontoon

  11. Hi, I have a 2012 model DT15 Suzuki.it has 3 wires from under the flywheel-YELLOW-PINK-PINK with YELLOW stripe.I am hoping they are from the lighting coil.If I want to hook these to a 4ah deep cycle battery do I need a voltage regulator and rectifier or just a rectifier.If only a rectifier is required which wires would hook to the rectifier and where would the third wire go.

  12. I HAVE A 25HP 4 STROKE YAMAHA MODEL F25C OUTBOARD NEED TO KNOW WHAT WIRES GO FROM THE SOLINOID TO THE STARTER CAN YOU SHOW ME HOW TO HOOK THEM UP

  13. YAMAHA 25 HP 4 STROKE 04 NEED TO KNOW WHAT WIRES GO FROM THE SOLINOID TO THE STARTER STEP BYE STEP SEND PICTURES PLEASE THANKS

  14. 12 volt plug not working on my 2018 2072.There is one wire not hooked up into the fastener coming from the starter switch.Could this be the one that operates 12 volt power????

  15. I have a 1976 20hp Mercury outboard that I need assistance with the switch box that has 7 color coded wires. The green wire and green/white wire I have hooked up properly, but, the other 5 wires, blue, white, red, Brown and orange don’t match up with my existing wires on my original switch box. Can u help me determine what wires go to correct terminals??

  16. I have a 1989 pf16 bass tracker. Had a 89 40 horse johnson tracker outaboard. The connection from controlers have a round plug. No tilt and trim. I changed motors to a 1998 35 horse johnson. The throttle and shift controls all worked but i cant figure out the wiring from the factory contols the the new motor. The motor came with a ignition switch the guy used to show it runs good. Either i make a harres using the switch the guy gave me or i splice connection the factory wires inplace of the switch he gave me. Please help me.

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Most Popular

Recent Comments